Due to vendor restrictions this product does not qualify for this offer.
Bulb Type: LED Board
Bulb/LED Color: Red
Sold in Units: Kit
Nice looking, solid unit. The only issue I had are the turn signals. The brake light worked out of the box, but the signal bulb socket contacts are wired one for ground, one for power. The bulbs however need the ground on the housing. So, you can either ground the entire housing, or just the turn signal socket itself to make it work. Also, if you have a V Star you may need to solder in a resistor (2w .33ohm) to the flasher relay, or use inline load equalizer to fix the 'hyper flash'. I had no luck finding a 5 pin solid state relay that is plug and play.
The Tombstone Tail/Stop/Turn Signal combo assembly is a nice looking assembly. Would be nicer if the turn signals were set a little bit further out. I would have rated this five stars if a few things were different. First, the assembly neither comes with a wire schematic nor a mounting diagram. Do not ask the Tech support guys as they do not know how to connect the light. This light came with 7 wires. Three black wires (1 for each turn signal run light, and the third wire is to be grounded to the body of the assy). 2nd, it would have been nice if the ground screw would have been included. Luckily, I had a very small screw with the correct thread. It comes with three red wires (one for each turn signal, the 3rd one is for the tail light brake.) Lastly, it comes with a yellow wire (tail light assy run). When speaking to tech support, they instructed that it was a brake light wire (WRONG). After downloading a schematic from J&P Cycles, there was no yellow wire included. This assembly’s turn signals is supposed to be strictly turn signals. I DO NOT RECOMMEND connecting the two “run” black wires to the bike’s run. 3rd, When operating the turn signals, you can barely see the signals flashing. Just tuck these away and only have the turn signals operate solely as turn signals. You may want to get a “three play” later on to use these as tail/turn/brake. The three “stripped” wires in the light operate the brake/tail light. Black=ground, Red=brake, yellow=tail/run. See picture for more clarity. Make sure you ground the light assy to the bike after mounting the assy on the bike by the use of a ground wire from the mount bolt to the fender, or by using the harness ground to the mounting bolt. 4th, the mount bolts are too short. And 5th, the license plate light is "yellowish" and does not light up the plate that well. Good luck with this assembly. I hope this review is helpful. As a heads up, this light was mounted onto a 2005 Suzuki Boulevard C90T. This does not provide a perfect fit. However, it is barely noticeable. One plus, this did come with the license plate bracket. I did not need it, but it was nice to have in case I did need it.
The taillight is just what I needed and arrived in a timely manner. The product and delivery met above my expectations being in Australia Thank you Derek
Easy to install and hook up. Looks great!
Awesome product, works perfectly
Exactly what you expect. High quality, good lighting.
Needs a wiring diagram! What's the yellow wire for?
IT FIT AND WORKS, CANN'T ASK FOR MORE THAN THAT.
Arrived in two days, with great packing.
I was a little nervous when ordering this light not knowing if it would fit . After ordering the part it arrived 3 days later , very fast shipping . Was very happy to see that it was a perfect match to the shape of my rear fender on my 2006 Suzuki C50 . I am VERY pleased with my purchase and will be returning to J&P for further purchases .
This would have been rated higher if some wiring instructions were included. However, I figured out that the red turn wires operated the brake (or turn light) and the black turn wire would operate the run lights if you grounded the body of the light. You can do that by using a grounding screw to the body and running it to the bike's tail light wire ground. The tail black is already a ground for that light. The lights themselves are real bright, but you will probably need a modulator if you now have regular bulbs in your turns.
Totally off the hook Just what I was looking for !
Love this set, easy to mount and hook up, the price is great too.
How about some wiring instructions guys? Otherwise great product.
Really like the look but it needs to have a wiring schematic with it for ease of installation.
Have used this tailight/turnsignal combo on three Harleys with only complaint being the turn signals are not bright enough on a sunny day. However when the LED board quits, there is no replacement. only choice-buy another complete tailight assy or change to another light.
This looks like what I'm going to need
The best quality and look
i ordered it so i could put my saddle bags on it looks great i'll well pleased whit the looks and price.
Love the look of this and the LEDs are nice and bright.
Description indicated that the license bar was not included. It was in the box and now I have a spare. Customer service did give me a refund. No wiring diagram included.
part is hi quality well made metalcast,nice chrome and will be able to accept modifications . thanksJP
Look is great. Difficulty wiring but managed.
Great tailight, looks great too, alot of compliments.
Looks great on my '05 Dyna Superglide. Took time to figure which wires connected to the OEM harness, but worth the price.
Email A Friend