Due to vendor restrictions this product does not qualify for this offer.
Sold in Units: Kit
|Electra Glide Anniversary FLH : 1978|
|Electra Glide Fat Bob FLHFB : 1970|
|Electra Glide FLB : 1970|
|Electra Glide FLBF : 1970|
|Electra Glide FLH : 1970–1978|
|Electra Glide FLH-80 : 1978|
|Electra Glide FLHB : 1970|
|Electra Glide FLHF : 1970–1975|
|Electra Glide Police FLP : 1971–1972, 1974–1975|
|Electra Glide Police FLPF : 1971–1972|
|Electra Glide Sport FLHS : 1977|
|Low Rider FXS : 1977–1978|
|Sportster 1000 Café Racer XLCR1000 : 1977–1978|
|Sportster 1000 Electric Start Anniversary XLH1000 : 1978|
|Sportster 1000 Touring XLT1000 : 1977|
|Super Glide Electric Start FXE : 1974–1978|
|Super Glide Kick Start FX : 1971–1978|
Looks very well made. Haven't ran it yet, may change the condenser out for bluestreak but would definitely buy again
The advance weights are very nice. good fit and great performance. I didn't use the rest of the kit so I can't rate the rest of the parts.
Advance unit is nice, points cam is nice, also. Very smooth on the needle bearings. Points and condenser are OK...alignment of top and bottom points contacts not perfect. All I wanted was the advance unit and the plate, though. Drilled 3/8" hole in plate to do advance timing with multimeter without a timing light, mounted Accel points and condenser to plate. Runs great. Wire to coil is a bit undersize. Runs fine, but I will probably replace with a heavier wire at some point.
I bought this just for the advance unit.Good quality upgrade from stock.
Great item - needle bearings should make for a long, worry free operation!
good set but no papers with it you have to know what your doing
well made fitment perfect
Fair price, Excellent condition
Have not put it on the bike yet, backing plate is thick and looks well made.
Be sure & check the movement on the roll pins, I just got mine & it only has 1/2 the movement it should have, the roll pins were way off centered . Maybe I just got a bad one. Will send it back.
The point set provided was not of the highest quality and was replaced. However, the kit installed well and the H-D 80-80 starts better than ever (the OEM electronic ignition was replaced). I recommend the upgrade set with needle bearings. Watch for the screw length on the coverplate, so as not to short out the points due to being too long.
advance mechanism was good but points and backing plate where not. Points where junk, would not mate flat at the contacts and the backing plate slot for timeing it where not as large as the one's in the factory plate, So I used a set of NAPA points and my old backing plate and everything worked out fine.
The ball bearing advance unit works great---smooth and free. The supplied points and condenser were hardly usable. Once replaced with a quality set, the unit performed as expected. If you're interested, Echlin (NAPA) points CS-7880 and condenser RR1750 work better than any points/condenser unit I've ever found.........and I've been riding for 45 years.
As usual, the shipping was fast! Easy installation! Parts look to be very well made. Works great on my 2001 Evolution Sportster! I would recommend this product to my friends.
Everything you need is there. I had points before I switched to electronic but am switching back after I had the electronic ignition fail because I can fix points on the road (usually). It does not come with any directions, so some may need a manual for directions.
All parts were easy to install and the bike has never run better since I have owned it.
Email A Friend
Select Your Motorcycle