Due to vendor restrictions this product does not qualify for this offer.
Everyday Low Price: $249.99
Gold Club Price: What's This? $224.99
J&P Part: 402-870
This product was proudly made in the USA
Manufacturer Part Number: 692-1612
Open or Closed Loop: Open
Sold in Units: Each
With/Without 02 Sensor: Without
|Touring Electra Glide Classic FLHTC : 2008–2009|
|Touring Electra Glide Standard FLHT : 2008–2009|
|Touring Electra Glide Ultra Classic CVO FLHTCUSE4 : 2009|
|Touring Electra Glide Ultra Classic FLHTCU : 2008–2009|
|Touring Road Glide CVO FLTRSE3 : 2009|
|Touring Road Glide FLTR : 2008–2009|
|Touring Road King Classic FLHRC : 2008–2009|
|Touring Road King FLHR : 2008|
|Touring Street Glide FLHX : 2008–2009|
|Trike Tri Glide Ultra Classic FLHTCUTG : 2009|
Installation takes a little more thinking. The original FI clips orientation presented a slight challenge. Once past that insatll was a breeze, Noticed a definite positive difference in overall performance with out of the box settings. great addition for the price.
So far so good very easy to install>
Works as advertised. Very easy install.
If you like tweaking your bike with exhausts, air cleaners etc. Then this is for you. Running around town I want a different baffle than I do on long rides. Sometimes a bro comes by and says hay try this out on your bike. Doesn't matter what it is. You can dial this Cobra in to a T in just minutes. You'll like it especially if you run EFI like I do. No mapping, needing a lap top, none of that. This is a great product.
Needed to add some fuel over the default setting. Bike runs great. Simple install.
Works Great with Vance and Hines Big Shots!!!
Works so far
Plug in and play, it delivered the enhanced performance as promised.
works great so far
easy to install and easy to use.
plug n play n more power!!
The heat is now gone and it rides so much smoother! EASY INSTAL!
Great product! Easy install, easy setup and easy calibration
I received the product just a few days after I had order it. The programmer I ordered is the Fi2000r fuel processor. It does what it said it would do. I didn't have to do any adjustments to it because it came programmed to my bike right out of the box. I do recommend this product to anyone that has aftermarket exhaust and needs a fuel processor system for their bike.
the FI2000r fuel processor was just what i needed after fitting a barron stealth air kit ,the FI2000r was so easy to install like Cobra say it's just plug an play and performance has been big improvement .and you cant complain about the price best value for money as far as I am concerned,and the customer service from JPs has been great as I am ordering over the net in austrailia.Dave. Perth .Western Australia
Works great, eliminates backfiring and lean stock mixtures. Definitely adds power but some mechanical knowledge recommended or installation and tuning.
Was bought for my nephew's Vulcan. He likes it alot.
Fast easy install, only 15 minutes
Works great, does everything it is suposed to
Easy to install. Did it myself in about 20 min.
was then easy install.cure my back fire problem...
The Fi2000 Tri port is super EZ to use, just plug & go. I didn't have to adjust at all.
No sweat installation and worked as advertised
Made a big difference in performance, but did cut down the fuel mileage by about 5 mpg.
After installing Vance and Hines exhausts. We purchased the F1200R Fuel Processor. It came preloaded for my bike. The installation was relatively easy thank god for Wayne. It was simple plug and play processor. No programming it no downloads great. I have noticed more torque and power. I would recommend this unit to anyone.
This is definately an asset for my Vulcan 1700 and the installation was a snap!
The product description states no backfiring and improved throttle response. My unit does neither of these. I can tell no difference at all.