Everyday Low Price: $69.99
Gold Club Price: What's This? $62.99
J&P Part: 8400075
This item qualifies for free ground shipping
|Sportster 1200 50th Anniversary XL 50 : 2007|
|Sportster 1200 CP XL1200CP : 2012|
|Sportster 1200 Custom XL1200C : 2005–2012|
|Sportster 1200 Forty-Eight XL1200X : 2010–2012|
|Sportster 1200 Low XL1200L : 2007–2011|
|Sportster 1200 Nightster XL1200N : 2009–2012|
|Sportster 1200 Roadster XL1200R : 2004–2009|
|Sportster 1200 Standard XL1200 : 2006|
|Sportster 883 Custom XL883C : 2004–2010|
|Sportster 883 Iron XL883N : 2010–2013|
|Sportster 883 Low XL883L : 2005–2010|
|Sportster 883 Roadster XL883R : 2006–2007, 2009–2011|
|Sportster 883 Standard XL883 : 2005–2009|
|Sportster Custom Limited A XL1200CA : 2014|
|Sportster Custom Limited A XL1200CA : 2013|
|Sportster Custom Limited B XL1200CB : 2014|
|Sportster Custom XL1200C : 2013–2014|
|Sportster Custom XL1200C Anniversary : 2013|
|Sportster Custom XL1200CP : 2014|
|Sportster Forty-Eight XL1200X : 2013|
|Sportster Roadster XL883R : 2014|
|Sportster Seventy-Two XL1200V : 2013–2014|
|Sportster SuperLow XL883L : 2011–2014|
Product as described, good enough... not so easy to install due to you must remove the top screw from each rear sock absorber, mines expanded a little bit causing that the new screws did not fit well... trying to compress the shock was difficult... better lift the by the rear fender and with the other hand fitting the screw in...
When installed, they pushed the bags out around three inches from the shocks. After pushing them in closer for an all around slimmer rear end, rust began to show through at the welds in a month.
well made, sturdy great looking and easy install!
Great part, easy install.
fit was perfect, fast and easy!
nice look when bags are not on
Fit my Iron883 perfectly!! I may buy the larger size as well for longer trips!
EZ to install--Great fit.
Works great hold quite a bit of stuff for your travels.
easy to install just as good as factory
08 Sportster. Brackets worked fine but the bolts that came with it did not thread in properly so just had to buy different bolts.
Installed these on my '04 XL1200C. The fit was perfect and the brackets and hardware are quality material.
High quality, easy to install. I would have preferred them in gloss black but did not see that offered.
Bag supports fit great and installed easy. Gives the bike a great new look.
Exceptional fit and performance.
Excellent value,beautiful chrome finish and a perfect fit.The only thing I suggest is use a spring compressor to hold the shocks.Holds my saddlebags perfectly and gives the big an awesome look from behind.Much better price than Harley!!
Well made, but did not fit my 2006 sporty XL 1200. I still used it by cutting it up and adapting it.
The only problem I had was the bolts that came with it were'nt long enough. Because of my sissy bar bolted at the same place. But I found the right size bolts at the hardware store.
Nice product but the rear bolts were not long enough. The bike was an 05 883L. Needed to be about 1/2 inch longer.
Brackets fit my '06 Sportster 1200c great. No complaints on this product.
Brackets came with 2.25in. 5/16in button head bolts. Bolts needed to be 3in. long to tie in through strut and nut under fender. Also recieved no instructions so I was cuaght off gaurd that my shocks would come completely off strut as bolt was being loosened. I would have supported suspension prior to instalation had I known that. Other than those two issues the product is fine.
Supports were a perfect fit. You can`t see them regardless with saddlebags on anyhow. The only problem I had was, I have a backrest with permanent sideplates and the bolt that was sent wasn't long enough to go through it. I had to buy a longer bolt.
I was told that having a detachable sissy bar would prevent me from placing this on to my 2004 Sportster 1200. This was incorrect, I just had to stop by a home and garden store to get a deferent set of bolts to use do to the extra length that was required. Other than that I am very happy with this.
The saddlebag supports bolted right up and I am very pleased with the product and price.
These get the job done. I was just wondering why they don't send replacement Torx bolts. They send Hex bolts and the one that they call 3/16" is actually a metric 5mm. In the directions it tells you that you will need a 3/4" combo wrench, but you actually use a 5/16" inch allen wrench.
The "SADDLEBAG SUPPORTS 04-05 XL" fit the '06 XL 1200R very well. However, if you have a detachable backrest, some of the bolts supplied in the kit will be too short. Two 3-1/2 bolts have to be purchased localy to complete the installation. If the 2 bolts would have been included I would have rated this product as "best".
These saddlebag supports fit my 2006 Sportster Custom great, & they are heavier built & look even better than I expected! Thanks J & P
Requires Adobe Flash Player