Cobra FI2000R Fuel Processor
J&P Part: ZZ40851
Everyday Low Price: $234.99
Cobra FI2000R Fuel Processor
• Nearly every fuel-injected motorcycle can benefit from the installation of the Fi2000R• Better throttle response, no backfiring, and smoother cruising are just a few of the areas improved by the Fi2000• When your engine has the proper air/fuel ratio metered to it, it can perform to its potential, run cooler and be a much more satisfying ride• Comes preset for your specific model• It is also set for your bike equipped with an aftermarket exhaust system• This setting will enhance the performance of the entirely stock bike as well• If you add a high-flow air filter system, you can quickly adjust your particular model because each comes with detailed instructions for making fine tuning adjustments• The Fi2000 increases horsepower and torque by optimizing stock lean air/fuel ratios (helps cool the engine temperature as well) No confusing computer downloads to install Pre-configured from the factory for your bike and model, but easy to adjust should your specific application need it| Manufacturer Part Number: | 92-1633 | Open or Closed Loop: | Open |
| Sold in Units: | Each |
If your motorcycle is not listed below, please click the 'Select A Motorcycle' button above so we can find the right part.
- Fury VT13000CX : 2012
- Fury VT1300CX : 2010–2011
- Interstate VT1300CT : 2011–2012
- Sabre VT1300C : 2011
- Sabre VT1300CS : 2012
- Stateline VT1300 : 2011
- Stateline VT1300CR : 2012
- VT1300CR Stateline : 2010
- VT1300CS Sabre : 2010
- VT1300CT Interstate : 2010
MrOliver Posted :
Out the box it took me about 20 minutes to install and back on the road. Installing this made a big difference that is very noticeable.
hmain84 Posted :
I received the product just a few days after I had order it. The programmer I ordered is the Fi2000r fuel processor. It does what it said it would do. I didn't have to do any adjustments to it because it came programmed to my bike right out of the box. I do recommend this product to anyone that has aftermarket exhaust and needs a fuel processor system for their bike.
djvanpad686 Posted :
the FI2000r fuel processor was just what i needed after fitting a barron stealth air kit ,the FI2000r was so easy to install like Cobra say it's just plug an play and performance has been big improvement .and you cant complain about the price best value for money as far as I am concerned,and the customer service from JPs has been great as I am ordering over the net in austrailia.Dave. Perth .Western Australia
mpeachey Posted :
Works great, eliminates backfiring and lean stock mixtures. Definitely adds power but some mechanical knowledge recommended or installation and tuning.
jacquesimmons Posted :
The Cobra FI2000 was very easy to install. Just plug and play. When I decided that I wanted to further tune device, it was just as easy. The directions are very easy to follow. It has really made a difference in the performance of the machine. My fuel mileage has dropped about two points, but the grin factor has increased several.
rwhite6683 Posted :
05-13-10 great product, easy to follow instructions 1 1/2 hour install.
putrzenski.christoph Posted :
Lots more get up and go, even though my bike ahs 30,000 miles.
nickfett Posted :
Fast easy install, only 15 minutes
scubberly Posted :
Works great, does everything it is suposed to
Allosoy Posted :
Easy to install. Did it myself in about 20 min.
vicblaster Posted :
The Fi2000 Tri port is super EZ to use, just plug & go. I didn't have to adjust at all.
gunnerfitz Posted :
No sweat installation and worked as advertised
athleticcc5 Posted :
Made a big difference in performance, but did cut down the fuel mileage by about 5 mpg.
Kaw_guy Posted :
This is definately an asset for my Vulcan 1700 and the installation was a snap!
Cobra FI2000R Fuel Processor?
Our customer service has the answer.
1-800-318-4823
